Window Replacement Suggestions
I am looking for information for replacing the large windows in our Rummer. I have spoken to one of the suggested people from this site - DS and he indicated that I need to find a glass person - not window company for the large format "windows" as they are not considered windows.
Any suggestions???
Thanks
CD
CD,
I had mine replaced by Canyon Glass. I was satisfied with their price and quality as well.
WM
Stan, have CD call me. We just replaced all of the back windows across the house and the large one in the kitchen for about $3k.
TK
Hi CD,
A few years ago, we replaced all of our large exterior glass with huge, double-pane panels. Every window company we talked to wanted to carve up the spaces with framing to accommodate their products. Ugh!
But Clear Choice was recommended to us by another Rummer Owner. The did a great job, (even with the trapazoids!):
PS - if you call Clear Choice, as for "Mo" - tell him RM sent you!
16285 SW 85th Ave. Suite 107 , Tigard, OR 97224
Phone 503-643-3887 | Fax 503-620-1153
clearchoiceconstruction.com [email protected]
http://www.clearchoiceconstruction.com/
We are thinking about doing the atrium next, and well certainly call them, first.
Good luck!
RM
Stan
Since I am new to your list I’m not sure what the protocol is here.
– FYI my experience from an ongoing remodel.
Canyon Glass Co
13075 SW Canyon Rd
Beaverton, OR 97005
503) 644-3153
I used Canyon Glass to make about 10-15 double pane windows; the largest was (54”x85”), I used a ¾ inch Al spacer, and most had a Low-E coating, (South facing windows in the sun). They can explain all the options and choices (glass, spacing, coating, etc).
I found their prices very reasonable, also I had them set the two largest, (carry them into the house and place them in the empty window opening, such that the window tape, (sealing the window) and trim (holding it in place) was all that needed to be done. The largest were extremely heavy windows, their hourly rate was low, and the time was minimal (measured in minutes) as the window openings were all prepped before they came. This minimal cost eliminated the risk of me breaking the window (getting it home and into the opening).
I did the demolition (removing the old window) and set the new trim (window casing) on one side before they arrived. I don’t know it they are full service, and will do the carpentry work and demolition. You may need a general contractor/remodeler/carpenter to do that work (if you cannot do it yourself). I’m sure they can recommend someone. For the heavy windows I would recommend your contractor have them set them too.
In the cases where they set the windows, they will come out and measure the size of the glass you need.
They also made many smaller windows which I measured, carried/set and installed.
It is more pleasant to replace your windows in the summer when it is warm and dry. Renting/owning suction cup handles for glass is a must.
Be sure to take the window dimension to the Post and Beam construction (in case you have a retro fitted double pane window), windows are measured from the outside looking in (important in specifying the location of the Low-E coating).
JB
Hi CD,
Your are correct in that the window companies don't know about just replacing the glass with an insulated glass unit (IGU). I used "Your Window Company" for the work. http://www.yourwindowcompany.net/.
I replaced the molding around each glass with new prepainted (by me) cedar. The IGU's were custom made with low-e double pane glass. The IGU's were manufactured in Tacoma WA.
If you are interested in seeing the work and understanding the costs, your welcome to visit my home or call me or both.
The attached picture from this April shows one of the more complicated IGUs being installed.
KS
Hi Stan,
We have had very good service from a company called "The Glass People" Ph. 503-690-8481.
They are able to replace large Rummer sized windows and the only company that was able to replace Rummer sized insulated glass windows, that I could find.
Hope this helps,
TMO
Hi CD,
We replaced our over sized windows with a solid piece of glass last year. Canyon Glass was able to install the double paned glass on all of our large windows (we have a pitched roof). If you would like to see how they look give me a call.
JH
Someone once suggested MS Glass. I know, the windshield company! Supposedly they offer doubled paned, argon filled glass panels at $20/sq. ft. Custom sizes and shapes are no problem. I haven't confirmed this information, but it couldn't hurt to check out.
-HL
As the previous owner of a "glass company", I strongly support that advice. Do get several bids as they are likely to be quite varied in price. Sorry, that I can not offer any specific recommendations, as my business was in California and several years ago.
TL
I just replaced alot of my windows with new high effiency glass and it wasn't that expensive. I used MS Glass to order the glass and got 3/16th double glazed windows in a Cardinal 366 series glass. http://www.cardinalcorp.com/products_coated_366/366.htm
The attached photo is a complete glass wall that I installed that is about 90" tall by 69" wide and cost about $590 for the glass. The top piece was $345 and the bottom was $245 because it's tempered and needs to be that way due to building codes.
It was also another $17 for the caulk and foam filler for the edges and $90 for the new wood because I needed to redo the window framing (the wood that actually holds the glass in) the bottom plate and the mullion bar to hold the top glass in place without bending. Also use stain on all of the new wood, not paint. The wood is still a little damp and the water in the wood will push the paint off and keep it from adhering properly. I used OSMO stain which protects better than any other stain on the market since most stains are just a colorant and use finishes that flake off over time. OSMO uses waxes that pentrate the wood and sit on top and resists water. It's also low VOC for your interior wood. It's available at EcoHaus in Portland. http://www.osmona.com
If you're doing it yourself, I can give you the specifics on how to do it correctly that'll produce the best results. I'd invite you to stop by and see it in person.
_am
Any suggestions???
Thanks
CD
CD,
I had mine replaced by Canyon Glass. I was satisfied with their price and quality as well.
WM
Stan, have CD call me. We just replaced all of the back windows across the house and the large one in the kitchen for about $3k.
TK
Hi CD,
A few years ago, we replaced all of our large exterior glass with huge, double-pane panels. Every window company we talked to wanted to carve up the spaces with framing to accommodate their products. Ugh!
But Clear Choice was recommended to us by another Rummer Owner. The did a great job, (even with the trapazoids!):
PS - if you call Clear Choice, as for "Mo" - tell him RM sent you!
16285 SW 85th Ave. Suite 107 , Tigard, OR 97224
Phone 503-643-3887 | Fax 503-620-1153
clearchoiceconstruction.com [email protected]
http://www.clearchoiceconstruction.com/
We are thinking about doing the atrium next, and well certainly call them, first.
Good luck!
RM
Stan
Since I am new to your list I’m not sure what the protocol is here.
– FYI my experience from an ongoing remodel.
Canyon Glass Co
13075 SW Canyon Rd
Beaverton, OR 97005
503) 644-3153
I used Canyon Glass to make about 10-15 double pane windows; the largest was (54”x85”), I used a ¾ inch Al spacer, and most had a Low-E coating, (South facing windows in the sun). They can explain all the options and choices (glass, spacing, coating, etc).
I found their prices very reasonable, also I had them set the two largest, (carry them into the house and place them in the empty window opening, such that the window tape, (sealing the window) and trim (holding it in place) was all that needed to be done. The largest were extremely heavy windows, their hourly rate was low, and the time was minimal (measured in minutes) as the window openings were all prepped before they came. This minimal cost eliminated the risk of me breaking the window (getting it home and into the opening).
I did the demolition (removing the old window) and set the new trim (window casing) on one side before they arrived. I don’t know it they are full service, and will do the carpentry work and demolition. You may need a general contractor/remodeler/carpenter to do that work (if you cannot do it yourself). I’m sure they can recommend someone. For the heavy windows I would recommend your contractor have them set them too.
In the cases where they set the windows, they will come out and measure the size of the glass you need.
They also made many smaller windows which I measured, carried/set and installed.
It is more pleasant to replace your windows in the summer when it is warm and dry. Renting/owning suction cup handles for glass is a must.
Be sure to take the window dimension to the Post and Beam construction (in case you have a retro fitted double pane window), windows are measured from the outside looking in (important in specifying the location of the Low-E coating).
JB
Hi CD,
Your are correct in that the window companies don't know about just replacing the glass with an insulated glass unit (IGU). I used "Your Window Company" for the work. http://www.yourwindowcompany.net/.
I replaced the molding around each glass with new prepainted (by me) cedar. The IGU's were custom made with low-e double pane glass. The IGU's were manufactured in Tacoma WA.
If you are interested in seeing the work and understanding the costs, your welcome to visit my home or call me or both.
The attached picture from this April shows one of the more complicated IGUs being installed.
KS
Hi Stan,
We have had very good service from a company called "The Glass People" Ph. 503-690-8481.
They are able to replace large Rummer sized windows and the only company that was able to replace Rummer sized insulated glass windows, that I could find.
Hope this helps,
TMO
Hi CD,
We replaced our over sized windows with a solid piece of glass last year. Canyon Glass was able to install the double paned glass on all of our large windows (we have a pitched roof). If you would like to see how they look give me a call.
JH
Someone once suggested MS Glass. I know, the windshield company! Supposedly they offer doubled paned, argon filled glass panels at $20/sq. ft. Custom sizes and shapes are no problem. I haven't confirmed this information, but it couldn't hurt to check out.
-HL
As the previous owner of a "glass company", I strongly support that advice. Do get several bids as they are likely to be quite varied in price. Sorry, that I can not offer any specific recommendations, as my business was in California and several years ago.
TL
I just replaced alot of my windows with new high effiency glass and it wasn't that expensive. I used MS Glass to order the glass and got 3/16th double glazed windows in a Cardinal 366 series glass. http://www.cardinalcorp.com/products_coated_366/366.htm
The attached photo is a complete glass wall that I installed that is about 90" tall by 69" wide and cost about $590 for the glass. The top piece was $345 and the bottom was $245 because it's tempered and needs to be that way due to building codes.
It was also another $17 for the caulk and foam filler for the edges and $90 for the new wood because I needed to redo the window framing (the wood that actually holds the glass in) the bottom plate and the mullion bar to hold the top glass in place without bending. Also use stain on all of the new wood, not paint. The wood is still a little damp and the water in the wood will push the paint off and keep it from adhering properly. I used OSMO stain which protects better than any other stain on the market since most stains are just a colorant and use finishes that flake off over time. OSMO uses waxes that pentrate the wood and sit on top and resists water. It's also low VOC for your interior wood. It's available at EcoHaus in Portland. http://www.osmona.com
If you're doing it yourself, I can give you the specifics on how to do it correctly that'll produce the best results. I'd invite you to stop by and see it in person.
_am